← H-Series overview

H-Series Specifications & Force Chart

Technical data for the Royal H-Series 3,000 PSI NFPA tie-rod hydraulic cylinder: full specifications, materials, all 23 mounting styles with NFPA codes, bore and rod sizes, a push/pull force chart and rod sizing guidance. Use it to size a new cylinder or match one you’re replacing.

3,000 PSInominal rating
1.5″–20″bore diameters
23mounting styles
36 in/smax speed

Jump to: Specifications · Mounting styles · Bore & rod sizes · Force chart · Rod sizing · FAQ

Request a QuoteDownload H-Series Catalogue (PDF)

H-Series Specifications

Nominal pressure rating3,000 PSI (derating may apply by mounting style)
Temperature range-30°F to 200°F (-34°C to 93°C); -40°C seals available
Maximum speed36 in/sec (0.91 m/sec)
Bore diameters1.50″ to 20.00″ (catalogue dimension tables cover 1½” to 8″)
Piston rod diameters0.625″ to 10.00″
ConstructionNFPA tie-rod, square head design, all steel
Mounting styles23 standard mounts
Rod ends6 styles; custom ends available
PistonOne-piece ductile iron, lock-nut retained, replaceable wear ring
CushionsOptional at either or both ends of stroke
Standard portsSAE O-ring boss (ORB); SAE Code 61 flange and NPTF optional

Construction and Materials

Piston rod

Hard chrome-plated C1045/C1050 carbon steel with a typical minimum yield strength of 85,000 PSI. Options: induction hardened chrome plated (IHCP), chrome-plated 17-4PH stainless, or Nitrotec treated (surface hardness up to 71 Rc with very good corrosion resistance).

Barrel

Very heavy-walled DOM C1026 steel barrel, micro-honed on the inside for low friction and long seal life, giving a robust and rigid cylinder assembly.

Heads

Precision-machined steel heads with spigots that protrude into the barrel for structural rigidity and precise alignment of the barrel and moving parts.

Piston

One-piece, non-threaded ductile iron piston attached with a nyloc nut, with a centred replaceable wear ring to prevent metal-to-metal contact.

Seals

Hallite Hythane piston cup seals and rod seal, plus a Hythane/Hyslip rod wiper with internal ribs that cleans the rod on the return stroke. Buna-N static O-rings, Viton optional.

Gland bushing

Long-wearing Rotocast bronze gland bushing for low friction and long bearing life. Ductile iron gland bushings with wear rings are available.

Cushioning

Optional cushions at either or both ends of stroke. The needle valve sits at port position 4 and a springless ball check at position 2 as standard.

Sensors and stops

End-of-stroke proximity sensors (TopWorx standard, or your preferred brand) and internal or external piston stops to reduce side-load stress on long strokes.

Mounting Styles

The H-Series is available in 23 standard mounting styles, matched to NFPA designations for drop-in replacement.

ModelMounting styleNFPA style
HCFixed ClevisMP1
HEPivot EyeMP3
HMPDetachable ClevisMP2
HWSelf-aligning EyeMPU3
HNMNo MountMX0
HNAExtended Tie-rods, Both EndsMX1
HNBExtended Tie-rods, Blind EndMX2
HNCExtended Tie-rods, Gland EndMX3
HRRod End Rectangular FlangeMF1
HRSRod End Square FlangeMF5
HBBlind End Rectangular FlangeMF2
HBSBlind End Square FlangeMF6
HGRectangular Gland End HeadME5
HHRectangular Blind End HeadME6
HTRRod End TrunnionMT1
HTBBlind End TrunnionMT2
HTMid TrunnionMT4
HFFoot MountMS2
HSSide TappedMS4
HDDouble RodMD
HCRCommon Rod—
HCHCommon Head—
HCCHRCommon Head + Common Rod—

Trunnion-mounted cylinders swivel in one direction and carry shear loads only; pins must be held rigidly and in accurate alignment.

Self-aligning eye (HW / MPU3) maximum operating pressure

Bore (in)Push (PSI)Pull (PSI)
1-1/21,8002,200
22,3003,000
2-1/21,5001,800
3-1/41,6001,900
41,9002,400
52,0002,400
61,8002,200
72,1002,600
82,3002,900

Ratings are based on the dynamic load capacity of the bearing.

Bore and Rod Sizes

Standard bore and rod combinations from the H-Series catalogue, with tie-rod thread, recommended tie-rod lock-nut torque and standard port size.

Bore (in)Rod diameters (in)Tie-rod threadTie-rod torque (ft-lbs, dry)SAE portNPTF port
1-1/25/8, 13/8-2420SAE -081/2″
21, 1-3/81/2-2045SAE -081/2″
2-1/21, 1-3/8, 1-3/41/2-2060SAE -081/2″
3-1/41-3/8, 1-3/4, 25/8-18100SAE -123/4″
41-3/4, 2, 2-1/25/8-18130SAE -123/4″
52, 2-1/2, 3, 3-1/27/8-14300SAE -123/4″
62-1/2, 3, 3-1/21-14500SAE -161″
73, 3-1/2, 41-1/8-12750SAE -201-1/4″
83-1/2, 4, 4-1/21-1/4-121,000SAE -241-1/2″

Full mounting dimensions for every model are in the H-Series catalogue PDF. All dimensions in inches.

Hydraulic Cylinder Force Chart

Theoretical push and pull force for every H-Series bore and rod combination. Push force = pressure × bore area; pull force = pressure × (bore area − rod area).

Bore (in)Rod (in)Bore area (in²)Annulus area (in²)1,000 PSI (lbs)2,000 PSI (lbs)3,000 PSI (lbs)
PushPullPushPullPushPull
1-1/25/81.771.461,7671,4603,5342,9215,3014,381
1-1/211.770.981,7679823,5341,9635,3012,945
213.142.363,1422,3566,2834,7129,4257,069
21-3/83.141.663,1421,6576,2833,3139,4254,970
2-1/214.914.124,9094,1239,8178,24714,72612,370
2-1/21-3/84.913.424,9093,4249,8176,84814,72610,272
2-1/21-3/44.912.504,9092,5039,8175,00714,7267,510
3-1/41-3/88.306.818,2966,81116,59213,62224,88720,433
3-1/41-3/48.305.898,2965,89016,59211,78124,88717,671
3-1/428.305.158,2965,15416,59210,30824,88715,463
41-3/412.5710.1612,56610,16125,13320,32237,69930,483
4212.579.4212,5669,42525,13318,85037,69928,274
42-1/212.577.6612,5667,65825,13315,31537,69922,973
5219.6316.4919,63516,49339,27032,98758,90549,480
52-1/219.6314.7319,63514,72639,27029,45258,90544,179
5319.6312.5719,63512,56639,27025,13358,90537,699
53-1/219.6310.0119,63510,01439,27020,02858,90530,041
62-1/228.2723.3728,27423,36656,54946,73184,82370,097
6328.2721.2128,27421,20656,54942,41284,82363,617
63-1/228.2718.6528,27418,65356,54937,30684,82355,960
7338.4831.4238,48531,41676,96962,832115,45494,248
73-1/238.4828.8638,48528,86376,96957,727115,45486,590
7438.4825.9238,48525,91876,96951,836115,45477,754
83-1/250.2740.6450,26540,644100,53181,289150,796121,933
8450.2737.7050,26537,699100,53175,398150,796113,097
84-1/250.2734.3650,26534,361100,53168,722150,796103,084

Values do not include friction, pressure losses or acceleration force. The PDF includes values at 500, 750, 1,500 and 2,500 PSI.

Rod Sizing and Piston Stops

To ensure adequate column strength, select the rod diameter using the effective rod length (Le = rod length fully extended × mounting factor K) and the maximum push force at your operating pressure. The full rod sizing table and K factors for each mounting style are in the catalogue.

A piston stop is recommended on long push-stroke cylinders to prevent gland and piston wear, rod buckling and jack-knifing. When Le exceeds 40″, add 1″ of piston stop for every 10″ over 40″. Gross stroke minus piston stop equals effective stroke, so increase the stroke if the working length must be kept.

Ports, Rod Ends and Accessories

SAE O-ring boss ports are standard, with SAE Code 61 flange, NPTF, oversize and manifold ports available, at any of four port positions. Rod ends come in six styles including KK and CC threads, full thread, female thread and rod-end couplers. Options include rod and thread extensions, wrench flats, high-temperature seals, cast iron piston rings and a brass rod scraper.

Matching rod clevises, pivot eyes, mounting brackets, pins and self-aligning rod eyes are available for every bore. See cylinder accessories →

H-Series FAQs

What pressure are H-Series hydraulic cylinders rated for?

The H-Series has a nominal rating of 3,000 PSI. Some mounting styles are derated; for example, the HW self-aligning eye mount is rated between 1,500 and 3,000 PSI depending on bore and direction, because it is limited by the bearing’s dynamic load capacity.

Are H-Series cylinders interchangeable with other NFPA cylinders?

Yes. The H-Series is built to NFPA mounting styles and dimensions, so it can replace NFPA-standard tie-rod cylinders. The one exception is the 2″ bore, where the heavier Royal barrel wall means the AA and R dimensions differ from NFPA.

What bore and rod sizes are available?

The catalogue lists standard bores of 1½”, 2″, 2½”, 3¼”, 4″, 5″, 6″, 7″ and 8″, with two to four rod sizes per bore from 5/8″ to 4½”. Bores up to 20″ and rods up to 10″ are available on request.

What seals do H-Series cylinders use?

H-Series cylinders use Hallite Hythane piston and rod seals with a Hythane/Hyslip rod wiper. Static O-rings are Buna-N, with Viton available for higher temperatures and seals rated to -40°C for cold climates.

What rod materials are available?

Standard rods are hard chrome-plated C1045/C1050 carbon steel. Options include induction hardened chrome plated (IHCP), chrome-plated 17-4PH stainless steel and Nitrotec-treated rods for corrosion resistance.

How do I calculate the force of a hydraulic cylinder?

Multiply the system pressure (PSI) by the piston area (in²). Push force uses the full bore area; pull force uses the bore area minus the rod area. The force table on this page gives both values for every H-Series bore and rod combination.

Can I get replacement seal kits and parts?

Yes. Genuine Royal seal kits include all seal components and wear rings, and Royal keeps a large range of stock parts for emergency repairs. Contact the factory with your cylinder model number.

Need an H-Series Cylinder Built to Spec?

Not sure which configuration you need? See the H-Series overview, or send us your bore, stroke, mounting style and operating pressure, or the model number of the cylinder you’re replacing. Royal has built hydraulic cylinders in New Westminster, BC since 1960.

Request a QuoteCall 1-877-637-6925Download the PDF